Dolmar TB4516CC

Scaricare : 0 File Size : 28 mb    Produttore : Dolmar  
Categoria : Benzo e seghe

. . . . . . . . . .13 Troubleshooting Chart . . . . . . . . . . . . . . . . . . . . . .19 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 Warranty Information . . . . . . . . . . . . . . . . . . . . . . .20 Parts List . . . . . . . . . . . . . . . . . . . .Inside Back Cover Copy the model and parent part number here: Copy the serial number here: Make sure you carefully read and understand this manual before starting or operating this equipment. THIS PRODUCT IS COVERED

Dolmar MS-245.4 U

Scaricare : 2 File Size : 11 mb    Produttore : Dolmar  
Categoria : Prodotti per il Giardino

Fuel leakage may lead to fire. If any leakage is detected during inspection, replace the oil pipe immediately. Fuel pipe INSPECTION OF BOLTS, NUTS AND SCREWS – Retighten loose bolts, nuts, etc. – Check for fuel and oil leakage. – Replace damaged parts with new ones for safety operation. CLEANING OF PARTS – Keep the engine always clean. – Keep the cylinder fins free of dust or dirt. Dust or dirt adhering to the fins will cause piston seizure. REPLACEMENT OF GASKETS AND PACKINGS In reassembling af

Dolmar MS-245.4 C

Scaricare : 20 File Size : 11 mb    Produttore : Dolmar  
Categoria : Prodotti per il Giardino

Always wear protective gloves! CAUTION: Start the Petrol Brushcutter only after having assembled it completely. For machines with bike handle models – Loosen knob (1). – Place handle (4) between handle clamp (2) and handle holder (3). – Adjust handle (4) to an angle that provides a comfortable working position and then secure by firmly hand-tightening knob (1). CAUTION: Do not forget to mount spring (5). MOUNTING OF HANDLE For machines with loop handle – Fix a barrier to the left side of the mac

Dolmar MS-245.4 UE

Scaricare : 5 File Size : 11 mb    Produttore : Dolmar  
Categoria : Prodotti per il Giardino

Engine stops soon Engine speed does not increase Insufficient warm-up Perform warm-up operation Choke lever is set to “CLOSE” although engine is warmed up. Set to “OPEN” Clogged fuel filter Clean Contaminated or clogged air cleaner Clean Abnormal carburetor Make request for inspection and maintenance. Abnormal drive system Make request for inspection and maintenance. Cutter blade does not rotate Loosened cutter blade-tightening nut Tighten securely Twigs caught by cutter blade or dispersion- pre

Dolmar MS-245.4 CE

Scaricare : 3 File Size : 11 mb    Produttore : Dolmar  
Categoria : Prodotti per il Giardino

– Open the choke lever progressively while checking the engine operation. Be sure to open the choke lever to the full in the end. – In cold or when the engine is cooled down, never open the choke lever suddenly. Otherwise, the engine may stop. 7) Warm-up operation Continue warm-up operation for 2 to 3 minutes. OPEN CLOSE Carburetor Primer Pump Note: – If the starter handle is pulled repeatedly when the choke lever remains at “CLOSE” position, the engine will not start easily due to excessive fue


Scaricare : 1 File Size : 8 mb    Produttore : Dolmar  
Categoria : Benzo e seghe

Failure to follow this procedure may result in injury to hand or fingers and may damage the starter mechanism. 5 10 feet 5a 6a Chain saw operating instructions For assembly follow the procedure in the appropriate section "Mounting Guide Bar and Chain" of this manual. DOLMAR chain, guide bar and sprocket must match each other (see the appropriate section in this manual). WARNING! Proper tension of the chain is extremely important. In order to avoid false setting the tensioning procedure must be f


Scaricare : 6 File Size : 8 mb    Produttore : Dolmar  
Categoria : Benzo e seghe

Otherwise the service life of the chain and guide bar will be reduced. Before starting work check the oil level in the tank and the oil feed. Check the oil feed rate as described below: Start the chain saw (see „Starting the engine”). Hold the running chain saw approx. 6" (15 cm) above a trunk or the ground (use an appropriate base). If the lubrication is sufficient, you will see a light oil trace because oil will be flung off the sawing device. Pay attention to the direction the wind is blowing


Scaricare : 5 File Size : 8 mb    Produttore : Dolmar  
Categoria : Benzo e seghe

Chain saws with significantly reduced kickback potential are available. 19 5 7 6 5 4 1 2 3 Lift the chain (6) over the sprocket (5). Using your right hand, guide the chain into the top guide groove on the guide bar (7). CAUTION: Note that the cutting edges along the top of the chain must point in the direction of the arrow! Position the guide bar (4) and push against the sprocket (5) as shown by the arrow. Mounting the guide bar and saw chain Use the universal wrench delivered with the chain saw


Scaricare : 17 File Size : 8 mb    Produttore : Dolmar  
Categoria : Benzo e seghe

Always follow safety precautions in the Owner’s and Safety Manual. Improper use can cause serious injury! The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Preserve this Manual carefully! ATTENTION! Suivez toujours les conseils de securite du present manuel d’emploi et de securite. Une utilisation incorrecte de la tronconneuse peut entrainer des blessures graves! Conservez avec soin ce manuel! Les g


Scaricare : 0 File Size : 8 mb    Produttore : Dolmar  
Categoria : Benzo e seghe

The reaction of the chain drives the saw straight back toward the operator causing loss of saw control. Pushback fre-quently occurs when the top of the bar is used for cutting (fig. 14). 14 15 When felling in the vicinity of roads, railways and power lines, etc., take extra precautions (see fig. 16). Inform the police, utility company or railway authority before beginning to cut. 13 45° 45° = cutting down area 2 1 2 First clear the tree base and work area from inter- fering limbs and brush and c