Log:
Scaricare : 11   File Size : 1 mb   Produttore : Planar  
Categoria : Saldatrici
@name

Operation is subject to the following two conditions: 1. this device may not cause harmful interference, and 2. this device must accept any interference received, including interference that may cause undesired operation. FCC WARNING This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipme

Scaricare : 0   File Size : 237 kb   Produttore : Campbell Hausfeld  
Categoria : Saldatrici
@name

Other positions require different techniques such as a weaving pass, circular pass, and jogging. A higher skill level is required to complete these welds. All work should be performed in the flat position if possible. For specific applications, consult an arc welding handbook. WELD PASSES Sometimes more then one pass is necessary to fill the joint. The root pass is first, followed by filler passes and the cover pass (See Figure 11). If the pieces are thick, it may be necessary to bevel the edges

Scaricare : 3   File Size : 237 kb   Produttore : Campbell Hausfeld  
Categoria : Saldatrici
@name

These welders are equipped with infinite amperage control to accurately select the proper current needed for various welding conditions. Internal components are thermostatically protected. This welder can weld up to 1/8” steel in a single pass. Recommended electrode size is 1/16” diameter for 15 amp circuits, up to 5/64” diameter for 20 amp circuits. For replacement electrodes, call (800) 746-5641 for the nearest dealer. Unpacking When unpacking, inspect carefully for any damage that may have oc

Scaricare : 0   File Size : 1 mb   Produttore : Campbell Hausfeld  
Categoria : Saldatrici
@name@name@name

5/64 in. (2 mm) H i g h 7 . Position the electrode to begin weld, lower the welding helmet or position the hand shield, and strike an arc. Adjust output setting as n e e d e d . 8 . When finished welding, turn welder off and store properly. Do not operate thiswelding machine with cracked or missing insulation on welding cables, electrode holder, or power cord. Every 3 months: Replace any unreadable labels on the welder. Use compressed air to blow all dust and lint from the ventilation o p e n i

Scaricare : 4   File Size : 698 kb   Produttore : Campbell Hausfeld  
Categoria : Saldatrici
@name@name@name

Longitud del Arco - la distancia entre el extremo del electrodo y el punto de contacto con la superficie de trabajo. Metal Basico - el material que se va a soldar. Union a tope - la union de dos miembros alineados aproximadamente en el mismo plano. Crater - el vacio que se forma cuando el arco hace contacto con el metal basico. CD o Corriente Directa - corriente electrica que se deplaza en un solo sentido. La polaridad (+ o -) determina el sentido del desplazamiento. CD Polaridad Reversa - ocurr

Scaricare : 0   File Size : 237 kb   Produttore : Campbell Hausfeld  
Categoria : Saldatrici
@name

These MIG items include but are not limited to; Contact Tips, Nozzles, Gun Liners, Drive Rollers, Felt Wire Cleaner. In addition, this warranty does not extend to any damage caused by the untimely replacement or maintenance of any of the previously listed CONSUMABLE parts. D. Any failure that results from accident, purchaser’s abuse, neglect or failure to operate products in accordance with instructions provided in the owner’s manual(s) supplied with the product. E. Pre-delivery service, i.e. as

Scaricare : 2   File Size : 269 kb   Produttore : Campbell Hausfeld  
Categoria : Saldatrici
@name

This instruction sheet is to be used in conjunction with the standard owner's manual included with the welder (IN198904AV). Please refer to this sheet for WS090001AV assembly instructions. A NOTICE~ Please read all warning instructions in the owner's manual before operating. Components The WS090001 comes with the following additional equipment: • Automatic amperage adjustment -low position for 1/16" rods and high position for 5/64" rods--for ease of use. • Cable storage clips (shown in Han

Scaricare : 9   File Size : 237 kb   Produttore : Campbell Hausfeld  
Categoria : Saldatrici
@name

A proper arc should be no longer then the diameter of the rod. The sound of a proper arc is a steady, crisp sizzle, similar to bacon frying. TRAVEL SPEED The travel speed is the rate at which the electrode is moved across the weld W Workpiece Normal Amps, Arc Length, Speed Amperage Too Low Amperage Too High Speed Too Fast Speed Too Slow Arc Length Too Long Figure 10 - Weld Appearance Arc Length Too Short 6 Models WS0900, WS0950, WS1000 and WS1020 Models WS0900, WS0950, WS1000 and WS1020 area (Se

Scaricare : 8   File Size : 1 mb   Produttore : Campbell Hausfeld  
Categoria : Saldatrici
@name@name@name

The polarity (+ or -) determines which direction the current is flowing. DC Reverse Polarity - occurs when the electrode holder is connected to the positive pole of the welding machine. Reverse Polarity directs more heat into melting the electrode rather than the work piece. It is used on thinner material. DC Straight Polarity - occurs when the electrode holder is connected to the negative pole of the welding machine. With straight polarity more heat is directed to the work piece for better pene

Scaricare : 59   File Size : 1 mb   Produttore : Campbell Hausfeld  
Categoria : Saldatrici
@name@name@name

Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or property damage! Retain instructions for future reference. Wire Feed TM Arc Welder BUILT TO LAST QUALITYASSURANCEPROGRAM Need Assistance? Call Us First! 1-800-746-5641 Description The Campbell Hausfeld WF1800, WF1900 and WF2000 are 70 amp, single phase 115 volt input, wire feed arc welding machines. The WF2000 is equipped with infinite wire speed control to





categorie